www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 t: (408) 452 - 5595 ; f: (408) 452 - 5596 nov. 201 2 specifications are subject to change without notice. ? berex 2012 rev. 1. 7 bc l 0 16b super low noise phemt chip (. 1 5 m x 16 0 m) the berex bc l 0 16b is a gaas super low noise phemt with a nominal 0. 15 micron gate length and 16 0 micron gate width making the product ideally suited for applications requiring very low noise and high associated gain, in frequencies of up to 40 ghz . the BCL016B offers high insertion gain and a low noise figure for broadband applications . the BCL016B is produced using state of the art metallization with si 3 n 4 passivation and is screened to assure reliability electrical characteristics ( t a = 25 c ) symbol parameter/test conditions test freq . min. typical max . unit nf noise figure (vds = 2v, id = 10ma) 12 ghz 18 ghz 0.4 0.6 db g a associated gain (vds = 2v, id = 10ma) 12 ghz 18 ghz 1 2 . 5 10.5 13.5 1 1.5 db p1db output power @ p1db (vds = 2v, id = 10ma) 12 ghz 13 14.5 dbm i dss saturated drain current (vgs = 0v, vds = 2v) 50 ma g m transconductance (vds = 2v, vgs = - 0.3v) 120 ms v p pinch - off voltage (vds = 2v, id = 200a) - 0.7 v bv gd gate - drain breakdown voltage, (ig = - 200 a, source open) 9 v bv gs gate - source breakdown voltage, (ig = - 200 a, drain open) 6 v r th thermal resistance, junction to back side (au - sn eutectic attach) 270 c/w product features ? low 0.4db typical noise figure @12 ghz ? high 13.5 db typical associated gain @12 ghz ? high p in of up to 20dbm ? 0. 15 x 16 0 micron recessed gate applications ? commercial ? military / hi - rel. ? test & measurement
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 t: (408) 452 - 5595 ; f: (408) 452 - 5596 nov. 201 2 specifications are subject to change without notice. ? berex 2012 rev. 1. 7 bc l 0 16b maximum rating (t a = 25 c) exceeding any of the above maximum ratings will result in reduced mttf and may cause permanent damage to the device. s - parameters (v ds = 2 v, i ds = 10 ma) freq [ g hz] s11 [ mag ] s11 [ang] s21 [ mag ] s21 [ang] s12 [ mag ] s12 [ang] s22 [ mag ] s22 [ang] 1 0.99 - 11.25 5.95 169.63 0.017 83.73 0.54 - 5.90 2 0.98 - 22.22 5.93 160.06 0.033 76.58 0.53 - 11.65 3 0.97 - 32.54 5.68 151.26 0.048 70.53 0.51 - 17.14 4 0.95 - 44.55 5.73 142.08 0.062 64.57 0.48 - 21.53 5 0.93 - 54.26 5.52 133.35 0.076 58.37 0.44 - 27.50 6 0.91 - 65.76 5.59 124.70 0.089 53.16 0.40 - 32.21 7 0.88 - 79.02 5.45 114.83 0.101 45.48 0.33 - 42.00 8 0.85 - 90.99 5.42 106.08 0.113 40.18 0.28 - 45.56 9 0.82 - 101.41 5.31 97.75 0.125 33.41 0.23 - 58.00 10 0.78 - 116.54 5.22 87.78 0.133 26.50 0.15 - 73.89 11 0.74 - 131.03 5.13 78.33 0.143 19.24 0.11 - 103.09 12 0.68 - 150.07 5.00 66.81 0.151 10.38 0.13 - 157.16 13 0.66 - 169.47 4.69 56.28 0.153 2.15 0.18 164.27 14 0.63 168.75 4.46 45.46 0.157 - 6.54 0.26 148.69 15 0.64 145.31 4.10 33.81 0.154 - 16.06 0.36 135.43 16 0.66 124.37 3.70 23.23 0.148 - 24.06 0.44 126.12 17 0.69 102.63 3.30 11.86 0.141 - 32.66 0.51 119.95 18 0.73 88.34 2.85 3.09 0.130 - 38.61 0.57 111.43 19 0.76 75.06 2.48 - 5.82 0.120 - 43.78 0.62 106.03 20 0.80 59.85 2.12 - 15.00 0.109 - 48.60 0.65 101.91 21 0.82 52.72 1.80 - 21.27 0.100 - 50.84 0.67 98.55 22 0.84 42.62 1.52 - 28.44 0.093 - 53.53 0.69 96.42 23 0.86 35.06 1.23 - 34.89 0.084 - 57.23 0.71 92.69 24 0.89 32.73 1.04 - 38.66 0.076 - 60.50 0.73 90.55 25 0.91 24.09 0.86 - 43.76 0.062 - 61.13 0.76 89.32 26 0.93 19.10 0.69 - 48.13 0.054 - 60.20 0.77 88.42 note: s - parameters include 12 mil gold bond wires: 1 gate wire , 1 drain wire , 4 source wires . reference planes are at the edge of substrates shown i n the wire bonding information figure below . symbols parameters absolute v ds v gs i ds i gsf p in t ch t stg p t drain - source voltage gate - source voltage drain current forward gate current input power channel temperature storage temperature total power dissipation 5 v - 3 v 50 ma 30 ma 2 0 dbm 150 c - 60 c - 150 c 200 m w
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 t: (408) 452 - 5595 ; f: (408) 452 - 5596 nov. 201 2 specifications are subject to change without notice. ? berex 2012 rev. 1. 7 bc l016b n oise parameter s (v ds = 2 v, i ds = 10 ma) frequency (ghz) nf min. (db) gamma opt. (mag.) gamma opt. (ang.) associated gain (db) normalized rn 2 0.16 0.827 3.649 20.460 0.188 3 0.18 0.810 15.551 19.580 0.181 4 0.19 0.783 27.376 18.740 0.171 5 0.20 0.752 30.667 17.920 0.164 6 0.21 0.712 34.528 17.140 0.156 7 0.23 0.668 36.600 16.390 0.149 8 0.24 0.623 37.402 15.670 0.143 9 0.26 0.582 33.305 14.990 0.143 10 0.30 0.519 37.280 14.490 0.128 11 0.35 0.449 37.264 13.920 0.124 12 0.39 0.395 39.953 13.430 0.111 13 0.43 0.318 44.861 12.970 0.103 14 0.47 0.228 55.706 12.600 0.087 15 0.51 0.105 88.026 12.210 0.073 16 0.55 0.113 - 164.031 11.860 0.061 17 0.59 0.287 - 126.824 11.580 0.062 18 0.61 0.461 - 106.229 11.290 0.098 19 0.67 0.606 - 89.016 10.980 0.201 20 0.71 0.703 - 73.513 10.700 0.304
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 t: (408) 452 - 5595 ; f: (408) 452 - 5596 nov. 201 2 specifications are subject to change without notice. ? berex 2012 rev. 1. 7 bc l016b p in _p out /gain, pae (12 ghz) frequency = 12ghz v ds = 2 v, i ds = 10 ma (tuned for power) wire bonding information always follow wire bonding diagrams recommended by berex for each device to achieve optimum device performance and reliability. as a general rule, bonding temperature should be kept to a maximum of 280c for no longer than 2 min utes for all bonding wires. using 1 mil. diameter, au bonding wires. 1. gate to input transmission line - length and height : 5 00 m x 250 m - number of wire(s): 1 2. drain to output transmission line - length and height : 5 00 m x 250 m - number of wire(s) : 1 3. source to ground plate - length and height : 3 50 m x 2 00 m - number of wire(s) : 4
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 t: (408) 452 - 5595 ; f: (408) 452 - 5596 nov. 201 2 specifications are subject to change without notice. ? berex 2012 rev. 1. 7 bc l016 b handling precautions : gaas fets are very sensitive to and may be damaged by electrostatic discharge (esd). therefore, proper esd precautions must be taken whenever you are handling these devices. it is critically important that all work surfaces, and assembly equipment, as we ll as the operator be properly grounded when handling these devices to prevent esd damage. die attach recommendations : berex recommends the e utectic die attach using au/sn (80/20) pre - forms. the die attach station must have accurate temperature contro l, and the operation should be performed with parts no hotter than 300c for less than 10 seconds. an inert forming gas (90% n 2 /10% h 2 ) or clean, dry n 2 should be used. use of conductive epoxy (gold or silver filled) may also be acceptable for die - attaching low power devices. shipping & storage : berexs standard chip device shipping package consists of an antistatic gel - pak, holding the chips, placed inside a sealed metallized bag. this packaging is designed to provide a reasonable measure of protection from both mechanical and esd damage. chip devices should be stored in a clean, dry nitrogen gas environment at room temperature until they are required for assembly. only open the shipping package or perform die assembly in a work area with a class 10,000 or better clean room environment to prevent contamination of the exposed devices. caution : this product contain s gallium arsenide ( gaas ) which can be hazar dous to the human body and t he environment. theref ore, it must be hand led with care and in accordance with all governmental and company regulati ons for the safe han dling and disposal o f hazardous waste. do not do not burn, destroy, cut, crush or chemically disso lve the product. do not lick the product or in any way allow it to ente r the mouth. exclud e the product from g eneral industrial wa ste or garbage and dispose of only in accordanc e to applicable laws and/or ordinances. disclaimer berex reserves the righ t to make changes without further notice to any products herein to improve reliability, function or design. berex does not assume any liability arising out of the application or use of any product or circuit described herein. life support policy berex products are not authorized for use as critical components in life support devices without the express written approval of berex. 1. life support devices or systems are devices or systems which (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labeli ng, can be reasonably expected to result in significant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or syst em, or to affect its safety or effectiveness.
|
